Murakami Aquasol HV Emulsion - Waterbase, Discharge, Plastisol
Murakami Aquasol HV Emulsion - Waterbase, Discharge, Plastisol

Murakami Aquasol HV Emulsion - Waterbase, Discharge, Plastisol

MUR HV

Murakami Aquasol HV has a higher vicsosity for thicker stencils. Fast exposures, and highly durable stencils provides non stop production on press. Use as is for sharp plastisol prints, or it can be made more water resistant with the addition of diazo or application of Murakami Hardeners. Aquasol HV is a pure photopolymer emulsion for plastisol, discharge, and water-based textile ink systems.

Product options:

29.99 $29.99

Physical Properties:

  • Blue colored PVA-SBQ Pure Photopolymer Direct Emulsion
  • Pre-sensitized for immediate use
  • Fast exposures, 3-5x faster than diazo based emulsions
  • Excellent for use with Plastisol, Discharge and Water-based ink systems
  • Virtually pin hole and fish eye free
  • Extremely durable on press
  • Suitable for use with water based inks when hardened with Murakami Hardeners
  • Outstanding resolution and definition properties
  • 42% solids content

Handling:  Handle under yellow safelights. Avoid exposure to sunlight, flourescent and incandescent lights.

Sensitizing:  This PVA-SBQ emulsion is ready to use.  There is no need to add sensitizer.

Mesh Preparation: It is important to remove any contamination, residual inks, cleaning chemistry, or general dirt and dust.  Haze/Ghost Remover (a non-caustic water soluble liquid)
will remove residual ink and/or emulsion. Screen Degreaser will help eliminate any further contaminants. Completely dry the screen before coating.

Coating Procedure:

  •  Use a clean dry coating trough that has a nick free surface for smooth coating.
  • Apply one or two coats of emulsion to the print side. Rotate the frame 180 degrees and apply one or two coats of emulsion to the squeegee side.
  • Additional coats may be added to the print side if thicker stencils are required.

Drying:  Dry the coated screen horizontally with the print side down in a clean light safe area.  The following will help to ensure complete drying:

  • 86° to 104° degrees F (30° to 40° C)
  • 30% to 50% relative humidity
  • Good air circulation

The use of a screen drying cabinet with heated airflow can help in maintaining these conditions.

Exposure:

Clean the film positives and vacuum frame glass prior to exposure to minimize pinholes. Exposure is affected by mesh color, emulsion type, coating thickness, lamp type and the age of the bulb itself.  For best results use an exposure calculator to determine the correct exposure time. It is important that a lamp designed for exposing screen printing emulsions is utilized.

Note: The use of film positives that are either frosted or have weak black density can reduce resolution and definition qualities of the coated screen.

Storage Handling:

Store the emulsion in a cool dry area. Unsensitized emulsion has a shelf life of at least one year when stored at room temperature. Use Murakami PVA-SBQ emulsion within one year for best results.  Coated screens may be stored for up to one month when kept under the following conditions.

  • 59° to 77° degrees F (15° to 25° C)
  • 30% to 50% relative humidity

Full Description

Physical Properties:

  • Blue colored PVA-SBQ Pure Photopolymer Direct Emulsion
  • Pre-sensitized for immediate use
  • Fast exposures, 3-5x faster than diazo based emulsions
  • Excellent for use with Plastisol, Discharge and Water-based ink systems
  • Virtually pin hole and fish eye free
  • Extremely durable on press
  • Suitable for use with water based inks when hardened with Murakami Hardeners
  • Outstanding resolution and definition properties
  • 42% solids content

Technical Specifications

Handling:  Handle under yellow safelights. Avoid exposure to sunlight, flourescent and incandescent lights.

Sensitizing:  This PVA-SBQ emulsion is ready to use.  There is no need to add sensitizer.

Mesh Preparation: It is important to remove any contamination, residual inks, cleaning chemistry, or general dirt and dust.  Haze/Ghost Remover (a non-caustic water soluble liquid)
will remove residual ink and/or emulsion. Screen Degreaser will help eliminate any further contaminants. Completely dry the screen before coating.

Coating Procedure:

  •  Use a clean dry coating trough that has a nick free surface for smooth coating.
  • Apply one or two coats of emulsion to the print side. Rotate the frame 180 degrees and apply one or two coats of emulsion to the squeegee side.
  • Additional coats may be added to the print side if thicker stencils are required.

Drying:  Dry the coated screen horizontally with the print side down in a clean light safe area.  The following will help to ensure complete drying:

  • 86° to 104° degrees F (30° to 40° C)
  • 30% to 50% relative humidity
  • Good air circulation

The use of a screen drying cabinet with heated airflow can help in maintaining these conditions.

Exposure:

Clean the film positives and vacuum frame glass prior to exposure to minimize pinholes. Exposure is affected by mesh color, emulsion type, coating thickness, lamp type and the age of the bulb itself.  For best results use an exposure calculator to determine the correct exposure time. It is important that a lamp designed for exposing screen printing emulsions is utilized.

Note: The use of film positives that are either frosted or have weak black density can reduce resolution and definition qualities of the coated screen.

Storage Handling:

Store the emulsion in a cool dry area. Unsensitized emulsion has a shelf life of at least one year when stored at room temperature. Use Murakami PVA-SBQ emulsion within one year for best results.  Coated screens may be stored for up to one month when kept under the following conditions.

  • 59° to 77° degrees F (15° to 25° C)
  • 30% to 50% relative humidity

MSDS

Murakami AquaSol HV MSDS