Printers Choice Dual Cure Emulsion (Pink)
Printers Choice Dual Cure Emulsion (Pink)

Printers Choice Dual Cure Emulsion (Pink)

RC PC Emulsion DCP

Printers Choice Dual Cure Emulsion (Pink) is a fast drying dual cure photo-emulsion and is recommended for textile printing with Solvent inks, UV ink systems, Plastisol, and short run Water Based inks.

64.99 $64.99

Printers Choice Dual Cure Emulsion (Pink) also has a very high solid content which makes for stronger durability and better resolution. Diazo is added normally, first by adding room temperature water, agitating, and then adding the solution to the emulsion. Allow the emulsion to stand for at least 2 hours to ensure any air bubbles introduced during mixing are released. Reclaiming Printers Choice Dual Cure Emulsion (Pink) is easy with River City Supply and Printers Choice Stencil Removers, which are available in concentrate and ready-to-use formulas.

Degrease - Using a mesh degreaser, work up a lather on both sides of mesh. Flood screen and frame thoroughly with water, then dry.

Coat - Slowly apply first coat to print side. Then coat squeegee side with one coat. If a thicker stencil is desired, additional coats may be applied to the squeegee side while the emulsion is wet. Note that one coat on each side with ChromaBlue is similar to four coats wet on wet with typical diazo based emulsions. Dry thoroughly between coats.

Dry - Thoroughly dry screen in horizontal position, print side down, using a totally dark, clean drying cabinet. Temperature should not exceed 110 degrees

Expose - Place emulsion side of photopositive in contact with print side of screen. Exposure times for can vary based on your light source and coating methods; accurate exposure is important for optimal results. An exposure calculator is highly recommended to dial in your exposure times.

Develop - Gently spray both sides of screen with lukewarm water, wait 30 seconds then gently wash print side of the screen until image is fully open. Rinse both sides thoroughly. Dry screen completely and you are ready to print

*Handle in light safe conditions and make sure to store in a cool dry place.

Full Description

Printers Choice Dual Cure Emulsion (Pink) also has a very high solid content which makes for stronger durability and better resolution. Diazo is added normally, first by adding room temperature water, agitating, and then adding the solution to the emulsion. Allow the emulsion to stand for at least 2 hours to ensure any air bubbles introduced during mixing are released. Reclaiming Printers Choice Dual Cure Emulsion (Pink) is easy with River City Supply and Printers Choice Stencil Removers, which are available in concentrate and ready-to-use formulas.

Technical Specifications

Degrease - Using a mesh degreaser, work up a lather on both sides of mesh. Flood screen and frame thoroughly with water, then dry.

Coat - Slowly apply first coat to print side. Then coat squeegee side with one coat. If a thicker stencil is desired, additional coats may be applied to the squeegee side while the emulsion is wet. Note that one coat on each side with ChromaBlue is similar to four coats wet on wet with typical diazo based emulsions. Dry thoroughly between coats.

Dry - Thoroughly dry screen in horizontal position, print side down, using a totally dark, clean drying cabinet. Temperature should not exceed 110 degrees

Expose - Place emulsion side of photopositive in contact with print side of screen. Exposure times for can vary based on your light source and coating methods; accurate exposure is important for optimal results. An exposure calculator is highly recommended to dial in your exposure times.

Develop - Gently spray both sides of screen with lukewarm water, wait 30 seconds then gently wash print side of the screen until image is fully open. Rinse both sides thoroughly. Dry screen completely and you are ready to print

*Handle in light safe conditions and make sure to store in a cool dry place.

MSDS

Printers Choice Dual Cure Emulsion Dual Cure Emulsion Safety Data Sheet