River City Graphic Supply, LLC

K Laser AMagic Holographic Foil

AMAGIC

AMagic Holographic is the family that moves: 71 patterns carrying a diffraction structure that splits light into shifting color as the garment moves, on the same 25″ × 200′ roll and the same press settings as the rest of the line. Cracked ice, shattered glass, sequins, hearts, stars, hexagons, carbon fiber, pixie dust, waterfall, flower power, scales, weave and a full run of holo rainbow across eight different bases. This is the loudest thing you can put on a garment with one screen of adhesive and a heat press.

71 holographic patterns
25″ × 200′ master roll
Press under 305°F, 8–15 sec
Peel warm or cold
Ships direct from K Laser — orders before 3:30 PM CT typically ship within one business day. Free shipping on orders over $200.

$173.99

Description

Light Split Into Shifting Color — K Laser AMagic Holographic Foil

AMagic Holographic is the family that moves: 71 patterns carrying a diffraction structure that splits light into shifting color as the garment moves, on the same 25″ × 200′ roll and the same press settings as the rest of the line. Cracked ice, shattered glass, sequins, hearts, stars, hexagons, carbon fiber, pixie dust, waterfall, flower power, scales, weave and a full run of holo rainbow across eight different bases. This is the loudest thing you can put on a garment with one screen of adhesive and a heat press.

A Hologram Is a Surface, Not a Color

Every other foil in the line gets its look from a metallized layer with a color in it. A holographic foil gets its look from microscopic structure embossed into the surface, which diffracts light and separates it into its component colors. The consequence is that the effect depends entirely on movement and light: a holographic print is spectacular on a body walking under stage lights and nearly invisible in a dim room, and it photographs differently from every angle. It is an effect you sell by showing, not by describing.

Embossed Structure Is What the Heat Destroys

The 305°F ceiling matters more here than anywhere else in the line. The diffraction pattern is physical relief measured in fractions of a micron, and heat plus pressure is exactly what flattens relief. Overheat a holographic foil and it does not simply dull — the structure collapses and the rainbow goes with it, leaving a flat metallic that looks like a mistake. Start at 295°F, 10 seconds, and treat the time as the variable you adjust.

The Prefix Tells You the Base Under the Rainbow

Eight entries on the dropdown are called Holo Rainbow because ZP02 is the rainbow structure and the prefix is the metal under it: S0 silver, G0 gold, HA copper, NA peridot, PC light rose, PG ultra pink, VB wisteria, BF seafoam. The base changes the character completely — rainbow over silver is bright and neutral, rainbow over copper is warm and reads bronze at rest. Same for the five Carbon Fibers, five Confetti, four Hearts and four Flower Power.

Why Fine Detail Fights a Holographic

A diffraction effect needs area to show itself. On a thin stroke or a small letter there is not enough surface for the eye to catch the color shift, so the print reads as a plain metallic and you have paid for an effect nobody sees. Bold shapes, thick strokes and large fills are where holographic earns its price. If your artwork is delicate, put the holographic in the fills and a solid foil in the line work.

What You Receive

A full 25″ wide, 200′ long roll of the AMagic Holographic pattern you select above. The diffraction structure runs the length of the roll, so the whole 25″ width is usable.

✓Roll size: 25″ wide × 200′ long
✓Colors in this family: 71, selectable above
✓Ships: Direct from K Laser, typically within one business day
✓Adhesive: Required and sold separately — three routes below

Which Color Is Right for You?

All 71 share one roll size and one set of press settings, so the only decision is which one. These are the groupings that match how customers actually ask for them.

If you want maximum rainbow
Holo Rainbow is the strongest color shift in the family and comes on eight bases. Over silver it is the brightest and most neutral. Over gold or copper it stays warm. Cracked Ice, Shattered Glass and Pixie Dust are the next step down in intensity and read as sparkle rather than as spectrum.
If you want a texture that happens to shift
Carbon Fiber, Weave, Scales, Pebbles and HyperPlaid read as a material first and a hologram second. These are the ones that work on adult and technical garments, where a full rainbow would be too much.
If you want a motif
Hearts, Stars, Confetti, Sequins, Flower Power, Hexagon and Lines. Each comes on two to five bases. Motif holographics sell hard on youth and event work and on anything aimed at a dance or cheer market.
If you are matching an existing garment
Pick the base to the garment and the pattern to the design. The prefix on the code is the base metal, so NCKP24 Champagne and G0KP24 Champagne are the same champagne pattern on different metals. Order one roll and test before committing to a colorway for a customer.

How to Apply Holographic Foil

Foil is not cut and weeded like heat transfer vinyl. Your artwork lives in the adhesive layer: you lay the adhesive down in the shape you want, cure it, then press a sheet of foil over the whole area and peel the excess away. Get the adhesive right and the foil step is almost trivial.

Step 1 — Choose your adhesive route

Screen print it, water-based
Matsui Foil Adhesive TFG 301 — Print the adhesive through a 60–110 mesh with a 75° squeegee, flood then print, and cure it at roughly 284–302°F for about three minutes. Water-based keeps the hand soft, which matters when the adhesive sits under a large foil area.
Screen print it, plastisol
Printers Choice Printable Adhesive — A non-phthalate plastisol adhesive base that prints like any other plastisol through a 60–110 mesh. Use it when the rest of the job is already plastisol and you do not want a second system on the press. Cure it at 320°F. That figure is the adhesive cure and nothing else — the foil itself still presses under 305°F, and confusing the two is the most expensive mistake in foil printing.
Cut and press it, no screen at all
Siser Cuttable HTV Adhesive — A cuttable adhesive film: cut the shape on a vinyl cutter, weed it, press it to the garment, then press the foil over the top. No screen, no squeegee, no cure oven. This is the route for one-offs, for names and numbers, and for anyone doing foil on a heat press alone.

Step 2 — Lay it down and press

1

Apply the adhesive in the shape of your design
Screen print it through a 60–110 mesh with a 75° squeegee, flood then print — or cut the shape from the Siser cuttable adhesive, weed it and press it to the garment. Fine detail and registration are decided here, not at the foil stage.
2

Cure the adhesive
Matsui water-based cures at roughly 284–302°F for about three minutes. Printers Choice plastisol cures at 320°F. The Siser cuttable adhesive needs no cure step at all. That 320°F is the adhesive’s cure temperature in a dryer, before any foil is involved — it is not a press setting.
3

Lay the foil shiny side up
The dull side is the transfer side and goes down onto the adhesive. Shiny side faces you. Getting this backwards leaves you with a pressed carrier and no foil on the garment, and it is the single most common first-time mistake.
4

Press under 305°F
Start at 295°F for 10 seconds at medium to firm pressure. The usable window is 8–15 seconds.
5

Peel warm or cold, then check it
Cold is the safer default: let it cool completely, then lift the carrier away. If the foil lifts with the carrier in places, re-cover and re-press those areas briefly rather than pulling harder.
TemperatureUnder 305°F — start at 295°F
Time8–15 seconds — start at 10
PressureMedium to firm
PeelWarm or cold
Foil orientationShiny side up, dull transfer side down onto the adhesive
⚠ DO NOT RUN IT HOT
K Laser caps this foil under 305°F and warns that excess heat damages both the color layer and the release coating. Overheated foil dulls or shifts shade and stops releasing cleanly, so it tears instead of transferring. There is no upside to extra temperature — if the bond needs more, add time.

K Laser AMagic Full Line — Find Your Match

Four families, one roll size, one set of press settings. Whichever you start with, the process is identical.

77 colors. Solid metallic colors, the metals, three blacks and eight mattes.
52 colors. Patterns printed into the film — leopard, roses, marble, tie dye.
9 colors. The fastest movers: bright silver, seven golds, and clear gloss.

Working in cut vinyl instead, or adding foil to an existing line? See heat transfer vinyl, flock and plastisol inks.

Why Buy from River City Supply?

💰 Authorized Dealer Pricing
Dealer pricing on the full K Laser AMagic line, and free shipping on orders over $200.
🚚 Ships Direct from K Laser
This line drop ships from the manufacturer, so it typically leaves within one business day rather than waiting on a transfer to our warehouse.
✅ Screen Printing Supply Since 2008
In the trade since 2008, and people on the phone who have actually pressed foil. (512) 454-0505 or [email protected].
💳 Equipment Financing Available
Building out a press or a cutter alongside the foil? Financing options here.

Frequently Bought Together

Foil does nothing on its own. It bonds only where adhesive has been laid down first, so one of these three has to go in the cart with it.

Matsui Foil Adhesive TFG 301 — Screen print it, water-based
Print the adhesive through a 60–110 mesh with a 75° squeegee, flood then print, and cure it at roughly 284–302°F for about three minutes. Water-based keeps the hand soft, which matters when the adhesive sits under a large foil area.
Printers Choice Printable Adhesive — Screen print it, plastisol
A non-phthalate plastisol adhesive base that prints like any other plastisol through a 60–110 mesh. Use it when the rest of the job is already plastisol and you do not want a second system on the press. Cure it at 320°F. That figure is the adhesive cure and nothing else — the foil itself still presses under 305°F, and confusing the two is the most expensive mistake in foil printing.
Siser Cuttable HTV Adhesive — Cut and press it, no screen at all
A cuttable adhesive film: cut the shape on a vinyl cutter, weed it, press it to the garment, then press the foil over the top. No screen, no squeegee, no cure oven. This is the route for one-offs, for names and numbers, and for anyone doing foil on a heat press alone.

Make It Catch the Light — Ship Today

Select your color above. Orders placed before 3:30 PM CT go to K Laser the same day and typically ship within one business day. Free shipping over $200. Not sure which color or which adhesive? Call (512) 454-0505 — it is a two-minute conversation and it saves a wasted roll.

Technical Specifications

K Laser AMagic Holographic Foil — Technical Specifications

SpecificationValue
TypeTextile heat transfer foil (K Laser AMagic)
FamilyHolographic
Colors available71
Roll size25″ wide × 200′ long
Adhesive requiredYes — water-based, plastisol or cuttable, sold separately
Adhesive mesh60–110 mesh, 75° squeegee, flood then print
Water-based adhesive cure~284–302°F (140–150°C) for about 3 minutes
Plastisol adhesive cure320°F — the adhesive’s cure in a dryer, not a press setting for the foil
TemperatureUnder 305°F — start at 295°F
Time8–15 seconds — start at 10
PressureMedium to firm
PeelWarm or cold
Foil orientationShiny side up, dull transfer side down onto the adhesive
FabricsCotton, blends, polyester and more — test first
CareWash inside out, cold, gentle cycle, no harsh detergent
ShipsDirect from K Laser, typically within one business day

Technical Sheets / Safety Data Sheets / Documents

FREQUENTLY ASKED QUESTIONS

Frequently Asked Questions — K Laser AMagic Holographic Foil

Why do eight products have the same name?

They are the same holographic rainbow structure over eight different base metals. ZP02 is the pattern; the prefix is the base — S0 silver, G0 gold, HA copper, NA peridot, PC light rose, PG ultra pink, VB wisteria, BF seafoam. Rainbow over silver and rainbow over copper look nothing alike at rest.

Will a holographic foil survive the press?

Yes, within the temperature ceiling. The effect is embossed structure, and heat with pressure is what flattens structure, so staying under 305°F matters more on this family than on any other. Start at 295°F for 10 seconds. If a test piece comes out looking like a plain metallic, the press was too hot, not too cool.

Why does my holographic print look flat in photos?

Because a diffraction effect needs a moving light source or a moving garment, and a single flash photograph gives it neither. Shoot it in daylight, off-axis, with the garment at an angle, and move while you shoot. This is worth knowing before you build a product listing around one.

Do I need adhesive to use this foil?

Yes, always. The foil carries no adhesive of its own and bonds only where adhesive has been laid down and cured first. There are three routes and we stock all three: Matsui Foil Adhesive TFG 301 if you screen print water-based, Printers Choice Printable Adhesive if you screen print plastisol, or Siser Cuttable HTV Adhesive if you want to cut the shape on a vinyl cutter and skip the screen entirely. Foil ordered without adhesive will not stick to anything.

What temperature and time do I press it at?

Under 305°F, which is K Laser’s own ceiling. Start at 295°F for 10 seconds at medium to firm pressure, shiny side up with the dull transfer side down onto the adhesive, and peel warm or cold. The usable window is 8–15 seconds. K Laser warns that excess heat damages the color and the release properties, so if the bond needs more, add time rather than temperature.

Which way up does the foil go?

Shiny side up, facing you. The dull side is the transfer side and goes down onto the adhesive. Getting this backwards is the most common first-time mistake and it leaves you with a pressed carrier and no foil on the garment.

Do I peel hot or cold?

K Laser allows either warm or cold. Cold is the safer default: let the piece cool completely, then lift the carrier away. If the foil lifts with the carrier in places, re-cover and re-press those areas briefly rather than pulling harder.

How big is the roll?

25″ wide by 200′ long. The width is the part people underestimate — at 25″ you can lay several designs across the sheet in one press rather than pressing them one at a time, which is where the real cost per print on foil comes from.

What mesh should I use for the adhesive?

60–110 mesh with a 75° squeegee, flood then print. A coarser mesh lays down more adhesive, which is what you want under a large foil area; go finer when the artwork has fine detail, because the detail lives in the adhesive layer, not in the foil.

How do I cure the adhesive before I press the foil?

Matsui water-based foil adhesive cures at roughly 284–302°F for about three minutes. Printers Choice plastisol adhesive cures at 320°F. The Siser cuttable adhesive has no cure step at all — cut it, weed it, press it to the garment, then press the foil over it.

Wait — the plastisol adhesive cures at 320°F but the foil presses under 305°F?

Correct, and keeping those two numbers apart is what separates a clean foil print from a ruined one. 320°F is the plastisol adhesive’s cure temperature, reached in a dryer or flash before any foil is involved. The foil then goes on in a separate step, on a heat press, under 305°F. Take the foil to 320°F and you damage its color layer and its release coating — the finish dulls or shifts and the carrier stops letting go cleanly, so the foil tears instead of transferring. Two steps, two temperatures, and the higher one never touches the foil.

Can I do foil without a screen printing setup?

Yes. Siser Cuttable HTV Adhesive is a cuttable adhesive film: cut the shape on any vinyl cutter, weed it, press it to the garment, then press the foil over the top. No screens, no squeegee, no cure oven. A heat press and a cutter is the whole requirement, which makes foil available to shops that have never printed a screen.

What fabrics does it work on?

Cotton, blends, polyester and more. Test first — the variable is usually the adhesive and the garment rather than the foil, and a polyester that scorches at press temperature is a garment problem, not a foil problem. Press a scrap of the actual garment before you commit a run.

Can I layer foil with other decoration?

Put the foil on last. It is a surface effect, and pressing anything over it dulls the finish you paid for. Butt colors up against each other rather than overlapping them, and if a design genuinely has to stack over foil, build it on a scrap and look at it under a bright light before you run it.

How should a finished garment be washed?

Inside out, cold, on a gentle cycle, with no harsh detergent. Give it 24 hours before the first wash so the adhesive fully sets, skip the fabric softener, and hang to dry or tumble on low. Never iron directly on the design. A foil finish shows wash wear before a flat print does, so inside out genuinely matters here.

Why does my foil look patchy or dented?

A mirror finish reflects whatever is under it, so an uneven press, a seam, a zip or a bit of grit reads as a visible dull patch or dent in a way it never would on a matte print. Press on a flat area, use a pillow where you need one, and check the test piece under a bright light at an angle rather than straight on.

What do the product codes mean?

On a solid color the code is just the color reference. On a pattern the suffix is the pattern and the prefix is the base metal it is printed on — so in S5AK01, AK01 is leopard and S5 is bright silver. That is why several entries share a name: same pattern, different metal underneath. The code is how you tell them apart.

How fast does it ship?

This line drop ships direct from K Laser, so it typically leaves within one business day rather than going out of our San Antonio warehouse. Shipping is free on orders over $200. If you need foil and adhesive together on a deadline, order them together and call us so we can tell you what is arriving from where.

Can I get a sample before buying a full roll?

Call or email and ask. Foil is one of the materials where a swatch genuinely answers a question a photograph cannot, particularly on the golds and on anything holographic or iridescent. (512) 454-0505 or [email protected].

Still have questions? Our team has pressed this foil.Call (512) 454-0505

Reviews

Reviews

    Only logged in customers who have purchased this product may leave a review.

    You May Also Like

    Additional Options

    icon-angle icon-bars icon-times