Saati Duralife 60 Durometer Urethane Squeegee Blade – Soft Screen Printing Squeegee Material
Saati
Saati Duralife 60 Durometer Urethane Squeegee Blade — premium urethane squeegee blade stock — sold per inch from a full 144″ roll. Soft 60 Shore A durometer. Maximum Ink Deposit — Soft Urethane Screen Printing Squeegee Blade. Saati Duralife urethane maintains consistent hardness and sharp edge quality longer than rubber blades, resisting solvents, plastisol, water-based, and discharge ink chemistry. Cut to your exact handle width. $1.00/inch.
✓60 Shore A Durometer — Soft
✓Saati Duralife Urethane — Not Rubber
✓Chemical & Solvent Resistant
✓Sold Per Inch — Cut from Full 144″ Roll
✓Works with Plastisol & Water-Based Inks
✓Made in USA Compatible Handles
💰 Best price per inch: Select the full 144″ roll option for the lowest cost per inch — the same Saati Duralife blade material, best value for shops replacing multiple blades or stocking up.
🚚 FREE Shipping on orders over $200|📦 In-Stock: Usually ships same or next business day|🏪 Free In-Store Pickup · San Antonio, TX
Price range: $1.00 through $99.99
Description
Saati Duralife 60 Duro — Soft Urethane Blade for Screen Printing
A 60 durometer blade is the softest standard option in screen printing — and softness means ink. When you need maximum ink deposit on the garment, a 60 duro blade delivers. The blade flexes more under squeegee pressure, allowing more contact time with the mesh and pushing more ink through each opening. It is the right choice for thick plastisol inks, textured or uneven substrates, low mesh counts (60–110), and any application where a heavy ink film is the goal.
Key Features
🔬
Saati Duralife Urethane
Premium urethane formulation — not rubber. Urethane maintains consistent durometer and edge sharpness longer, resists solvent-based cleaners, plastisol oils, and water-based ink chemistry without swelling or softening.
📏
60 Shore A Durometer
Measured to 60 on the Shore A hardness scale. Soft — maximum flex and ink deposit.
✂️
Sold Per Inch — Cut from Full 144″ Roll
Order exactly the length you need from a full 144″ roll. Blade stock cuts cleanly with a sharp utility knife or guillotine cutter. Fits any standard squeegee handle that accepts replacement blade stock.
🧪
Chemical Resistant
Urethane resists swelling and softening from plastisol solvents, water-based ink chemistry, discharge activators, and screen cleaning chemicals including mineral spirits and ink degradants.
🔪
Sharpenable Edge
Saati Duralife urethane sharpens cleanly on standard squeegee sharpeners. A consistent, sharp edge restores print quality and extends blade life significantly beyond the first sign of edge wear.
🏭
Professional Grade
The same blade material used in high-volume production shops — engineered for consistent performance across hundreds of thousands of prints when properly maintained.
When to Use a 60 Durometer Blade
🧱
Textured & Uneven Surfaces
60 duro blades flex to conform to uneven textures — canvas, denim, fleece, and other non-flat substrates where a rigid blade would skip over surface variations.
🎨
Thick Ink Deposit
Simulated process printing, underbase printing, and any work calling for heavy ink deposit benefits from the 60 duro’s greater flex and ink push-through.
📏
Low Mesh Counts (60–110)
At low mesh counts, the openings are large and the ink is thick — a soft blade complements this combination, applying consistent pressure without requiring excessive downward force.
🌈
Specialty & Puff Inks
Puff inks, high-density plastisol, and other thick specialty inks require a heavy deposit to activate their effect. A 60 duro maximizes ink through the screen.
⚠️ When NOT to use 60 duro: Fine detail work, halftone printing, or high mesh counts above 200. The extra flex that makes 60 duro great for heavy deposit creates edge blur and inconsistent dot gain on fine halftone and detail printing.
See It in Action: Understanding Squeegee Durometer
📐 Understanding Squeegee Durometer
Durometer is the Shore A hardness rating of the squeegee blade — a standardized measurement of how stiff or flexible the blade material is. It directly determines how much ink passes through the mesh and the sharpness of the printed edge.
↑ Softer (60)
More flexible → more pressure on mesh → more ink deposit → heavier prints
⚖️ Medium (70)
Balanced → versatile across inks, mesh counts, and substrates → the shop standard
↓ Harder (80)
More rigid → less flex → less ink deposit → sharper edges → fine detail
Full Durometer Selection Guide
| Durometer | Feel | Best For | Product |
|---|---|---|---|
| 60 ← This Product | Soft | Textile printing: thick inks, heavy garment textures, low mesh counts (60–110). Simulated process printing on textured surfaces. Maximum ink deposit. | This product |
| 70 | Medium | General garment printing: plastisol and water-based on flat textiles, standard mesh (110–200). The most versatile durometer — the starting point for most shops. | 70 Duro Blade |
| 80 | Hard | High mesh / fine detail: halftones, process printing, 4-color process, fine line work, high mesh counts (200–305+). Less ink deposit, sharper edge definition. | 80 Duro Blade |
| 70/90/70 | Triple | Best of both worlds: soft outer layers (70) grip the fabric and conform to the mesh — hard center core (90) provides rigidity without fatigue. Most popular triple for general garment printing. | 70/90/70 Triple |
| 60/90/60 | Triple | Maximum ink deposit with rigidity: softest outer layers (60) for maximum conformance and ink transfer — hard center (90) for blade stability. Heavy ink deposit jobs, thick plastisol, specialty inks. | 60/90/60 Triple |
🔬 Why Urethane? Saati Duralife vs. Standard Rubber
Saati Duralife Urethane
- Resistant to plastisol, water-based, and discharge inks
- Resistant to solvents and screen cleaning chemicals
- Maintains consistent durometer across the blade lifespan
- Holds a sharper edge longer between sharpenings
- Lower abrasion wear on emulsion stencils
Standard Rubber Blades
- Can swell or soften when exposed to solvents
- Durometer drifts over time as rubber degrades
- Loses edge sharpness faster
- Lower cost upfront, but higher replacement frequency
🔧 Squeegee Blade Care & Sharpening
- Clean blades immediately after printing — dried ink hardens on urethane and requires more aggressive cleaning, which accelerates edge wear.
- Store blades edge-up or hanging — never lay a squeegee flat with blade down. The edge deforms under the handle weight over time.
- Sharpen regularly — a dull blade requires more pressure to shear ink through the mesh, which increases mesh wear, stencil wear, and wrist fatigue. Sharpen when you notice ink deposit becoming uneven or edges ragged.
- Inspect for nicks and flat spots — a nicked blade leaves streaks and uneven ink deposit. Sharpen past the nick or replace the blade section.
- Use a squeegee sharpener or lap grinder — hand sharpening on sandpaper creates uneven bevels. A dedicated sharpener produces a consistent edge across the full blade length.
All Squeegees & Blades at River City Supply
| Product | Format | Best For |
|---|---|---|
| Saati 60 Duro Blade | Blade only — sold per inch from 144″ roll | Soft — max ink deposit, textures |
| Saati 70 Duro Blade | Blade only — sold per inch from 144″ roll | Medium — general purpose |
| Saati 80 Duro Blade | Blade only — sold per inch from 144″ roll | Hard — fine detail, halftones |
| Saati 70/90/70 Triple | Blade only — sold per inch from 144″ roll | Triple — versatile with rigidity |
| Saati 60/90/60 Triple Roll | 144″ roll | Triple — max deposit + rigid core |
| Saati Duralife Roll | 144″ roll | Bulk blade stock |
| Nortech Wood Handle 70 Duro | Complete squeegee | Made in USA, general printing |
| Custom Wood Handle Squeegee | Any size | Custom width + durometer |
| Ergo-Force Handle | Ergonomic handle | Reduces fatigue, precision control |
| Squeegee Rack (8-slot) | Accessory | Stores 8 squeegees, wall-mount |
Need help choosing the right blade hardness?
Call us at (512) 454-0505 Mon–Fri 9am–5pm CT
Technical Specifications
| Specification | Detail |
|---|---|
| Product | Saati Duralife 60 Durometer Urethane Squeegee Blade |
| Brand | Saati — Duralife Series |
| Durometer | 60 Shore A — Soft |
| Material | Urethane (not rubber) — chemical and solvent resistant |
| Format | Sold per linear foot — cut to your required handle width |
| Thickness | Standard screen printing squeegee profile — fits standard handles |
| Edge Profile | Square edge (standard screen printing profile) |
| Ink Compatibility | Plastisol, water-based, discharge, UV, solvent-based inks |
| Chemical Resistance | Resistant to plastisol solvents, water-based chemistry, discharge activators, screen cleaning chemicals |
| Sharpenable | Yes — sharpens cleanly on standard squeegee sharpeners |
| Best Mesh Range | 60–110/inch |
| Best Ink Types | Thick plastisol, specialty inks, puff, heavy deposit |
| Available Sizes | Sold per inch from a full 144″ roll — cut to your required handle width |
Technical Sheets / Safety Data Sheets / Documents
FREQUENTLY ASKED QUESTIONS
When should I use a 60 vs. 70 durometer blade?
Use 60 duro when your print goal is maximum ink deposit — heavy plastisol, textured substrates, low mesh counts, underbase layers, or puff ink. Use 70 when you need a versatile blade for general garment printing across a range of inks and mesh counts. If you’re not sure, start with 70.
Can I sharpen a 60 durometer urethane blade?
Yes — urethane blades sharpen well. When the edge becomes dull or develops flat spots, sharpen with a dedicated squeegee sharpener to restore a clean, even edge across the full blade length.
How long does a Saati Duralife blade last?
Urethane blades last significantly longer than rubber blades because urethane maintains its durometer and edge quality over time. Lifespan depends on printing volume, substrate abrasiveness, and sharpening frequency — but a properly cared-for urethane blade can last for hundreds of thousands of prints.
How do I cut Saati Duralife blade stock to length?
Use a sharp utility knife with a straightedge guide, a guillotine-style paper/blade cutter, or a circular saw for high-volume cutting. Urethane cuts cleanly with a sharp blade. Make sure your cut is perfectly square to the blade length for an even printing edge across the full width.
What handle styles are compatible with Saati Duralife blades?
Saati Duralife blades fit any standard squeegee handle that accepts replacement blade stock — including Nortech wood handles, aluminum handles, and auto press squeegee heads. Confirm the blade slot width matches your handle spec before ordering.
Need help choosing the right blade hardness?
Call us at (512) 454-0505 Mon–Fri 9am–5pm CT
Reviews
Only logged in customers who have purchased this product may leave a review.
You May Also Like
Related products
-
Custom Squeegee with Wood Handle
$2.20 -
Saati Duralife 70 Durometer Urethane Squeegee Blade – Versatile Screen Printing Squeegee Material
Price range: $1.00 through $99.99 -
Saati Duralife 80 Durometer Urethane Squeegee Blade – Precision Screen Printing Squeegee Material
Price range: $1.00 through $99.99 -
Saati Duralife 60/90/60 Triple Durometer Urethane Squeegee Blade – Versatile Screen Printing Squeegee Material
$190.08
Reviews